成人精品一区二区久久久 I 国产美女永久无遮挡 I 中文字幕+乱码+中文字幕明步 I 国产在视频一区二区三区吞精 I 日韩精品小视频 I 成人性生交大片免费4 I 免费aaa级毛片在线视频 I 一级片毛片 I 大型成人社区 I 国模在线播放 I 欧美大荫蒂毛茸茸视频 I 偷偷色噜狠狠狠狠的777米奇 I www.久久亚洲 I 日日搞夜夜操 I 亚洲成色777777女色窝 I 毛片黄色毛片 I 午夜片在线观看 I 国产一区二区三区中文字幕 I 天天干夜夜骑 I 日韩在线视频一区二区三区 I 久久久无码精品亚洲a片0000 I 写真福利片hd在线播放 I 欧美成人一区二免费视频 I 色噜噜狠狠爱综合视频 I 中文字幕无线码免费人妻 I 国产精品久久久久久久久久不蜜臀 I 欧美综合人人做人人爱 I 1024成人网色www I 国产精品视频一二三区 I 亚洲免费美女视频

大家好！
不知大家有沒有使用過CP1L-EM40DT-D PLC 或者Ethernet通信模塊 CP1W-CIF41和CCD進行通信？這款PLC或通信模塊可否達到和CCD進行接收/發送數據的功能？
現在我有個項目使用到康耐視的CCD，支持Ethernet通信，康耐視相機關于通信協議的說明如下文：
   EtherNet/IP is an application level protocol implemented on top of the Ethernet TCP/IP and UDP/IP layers. It shares its object model with ControlNet and DeviceNet through the common Control and Information Protocol (CIP). This protocol allows the transfer of data and I/O over Ethernet.
      EtherNet/IP uses the standard Ethernet physical layer, and standard Ethernet and Internet protocols (TCP/IP, and UDP/IP) to transmit data. Because TCP/IP is a point-to-point topology, EtherNet/IP only uses this layer for explicit messaging; i.e. those messages in which the data field carries both protocol information and instructions for service performance. With explicit messaging, nodes must interpret each message, execute the requested task and generate responses. These types of messages are typically used to transmit configuration, diagnostic and event data.
     The UDP/IP protocol layer, which has the ability to multi-cast, is used for implicit messaging. With implicit messaging, the data field contains only real-time I/O data; no protocol information is sent because the meaning of the data is pre-defined at the time the connection is established, which in turn minimizes the processing time of the node during run-time. Implicit messages are short, occupying low-overhead, which allows for the time-critical performance needed by controllers.
**************************************************************************************************************************************************************************************************
因?yàn)镃J系列的PLC超出了費用預算，所以我想用CP1H或CP1L系列的PLC完成和相機之間的Ethernet通信！
不知可否？麻煩各位高手指點一下！
以上，謝謝!